Ultra Clear epoxy boasts the most advanced level of shine, gloss, reflectivity, clarity and depth, and it locks in those optical qualities forever. The most sophisticated system of synthetic polymeric-based protection available. Our Commercial-grade epoxy is engineered specifically for Bar Tops, Tabletops & Countertops.
--Can make the whole coating project to determine the role of color, luster bright, smooth and lively, the abrasion resistance, acid and alkali resistance, oil resistance, resistance to water, dust, etc. In common it is clear ,100% solid content ,two components of epoxy resin and hardener ,with the mix ratio of 2:1.To make the finished top coat much more glossy and brighter.
Technical Data Sheet
Mix Ratio by weight
Compressive Strength (Mpa)
Wear resistance (mg)
Shelf Life (M)
5kgs/10kgs/20kgs per Barrel ,accept OEM&ODM
How to use MTB-3309 Ultra Clear Table Top Epoxy Coating /Extremely Durable Table Top Finish?
No experience needed.Get a beautiful crystal-clear surface in just a few easy steps.
Step 1: Measure Epoxy MTB-3309 Clear Epoxy is a two-part, epoxy coating that is mixed at a 2 to 1 ratio. Pour an equal amount of hardener and resin into a new container. It is important that you use a new container for each batch that you mix so that the next batch does not get contaminated from the remnants of curing epoxy in the previous container.
Step 2: Mix Epoxy Mix thoroughly with our mixing drill bit to ensure that the batch is completely blended.
Step 3: Paint on a Seal Coat of Epoxy On porous material such as wood, you will need to paint on a seal coat of the same epoxy first to seal any pores in the surface. This prevents air bubbles from forming in the following flood coat. Not all surfaces require a seal coat. Contact customer service if you are unsure if your project will need a seal coat as you will need to figure the seal coat into your epoxy order to make sure you have enough product.
Step 4: Pour Epoxy Flood Coat Pour the epoxy onto the surface working your way down the length of the area. The epoxy self levels so there is no need to move it around with any tools. The epoxy coat can be allowed to flow over the sides which will create a coating on the vertical edges. The epoxy that drips over will form bumps about 1/2 inch underneath the lip of the edge. These drips can be sanded off once the epoxy has cured. *Multiple flood coats can be applied to cover over embedded objects. Just pour a new flood coat every 4 hours.
Step 5: Pop Air Bubbles with a Plumber’s Torch or Heat Gun Once you finish pouring the epoxy, you will need to pop air bubbles using a plumber’s torch or a heat gun (not a hair dryer). This process is the easiest step as it only takes about 30 seconds to 1 minute to do. Keep the torch or heat gun a few inches from the surface and simply wave it back and forth until you cover the entire distance of the surface. The heat pops any bubbles instantly.
The epoxy is dry to the touch in 12 hours. Allow 72 hours before using the surface. That’s it!
Working Temperature of MTB-3309 Clear Ultra Clear Table Top Epoxy Coating /Extremely Durable Table Top Finish
The working room temperature must be above 75 degrees, several hours prior to mixing the epoxy. We recommend that the product be brought inside and acclimated to room temperature, as it will be cold during winter shipping months. Use space heaters if necessary to ensure the temperature remains above 75 degrees in cold areas, such as garages and basements. It is extremely important that the temperature remain above 75 degrees for a full 72 hours, in order for the epoxy to cure. High or low humidity and higher temperatures (75-110 degrees) are perfectly fine for curing; the epoxy cures much faster with higher temperatures.
Epoxy Resin (A)
MTB-3307Epoxy Prmimer (per square meter)
MTB-3308 Epoxy Base Coat
(per square meter)
MTB-3309 Epoxy Topcoat
(per square meter)
Packing & Delivery
MTB-3309 Clear Table Top Epoxy Coating
We have two types packages for you choice
---In common ,it takes about 1-3 days to prepare the cargoes for you after you confirm the order.The exact time depends on your quantity.
Why choose us ?
1. Professional manufacturer & long history
We are direct manufacturer of glue and adhesive since 1998.So We have Professional production team, production line, experienced technical experts also much experiences and higher skills to ensuring product quality and deliver in time with a very short time .
2. Competitive quality &factory price
3. Our market
Our customer all over the world . Main market in Europe ,USA ,South America,Australia and Asia ,such as Vietnam,Thailand , Malaysia and so on .
We gained good reputation in the industry because our various items made of imported raw material, good workmanship and fast delivery time.
4. Custom design welcome
Customer logo /design/OEM welcome .So our products always so creative&innovative .
5. Best service
We keep every customer for long time business.We regard every one as our VIP,no matter small or big order .